Automower-fans

Bonjour a tous,

tout est dans le titre .... qq a-t-il une idee de la signification de ce code ....

et encore mieux, si qq avait la liste des codes ... cela serai super !!!

A+

Jean-luc

ause
number
Message Description
1 Internal use
2 Blocked path Bumper event was received during GO sequence
3 Start elsewhere Software problem – bumper related
4 Start elsewhere Software problem – bumper related
5 Start elsewhere Software problem – bumper related
6 Start elsewhere Software problem – bumper related
7 Drive overload Drive motor overload
8 Low battery Very low battery voltage
9 Start elsewhere Software problem - wire related
10 Drive problem Problem in the odometer (drive wheels are active but odometer
pulses are not detected)
11 Drive overload Drive motor overload
12 Frnt wheel prob. We exceeded the allowed front wheel detection time (drop-off)
13 D.K. problem DK problem
14 Start elsewhere
DK current calibration failure
(during the mowing motors activation in the GO sequence)
15 Start elsewhere Software problem
16 Start elsewhere Software problem - wire related
17 Start elsewhere Software problem
19 Start elsewhere Robot got stuck because of multiple drive over current events
20 No wire signal Mechanism for recovering from electricity power interruption during
automatic operation has failed
21 Mowing overload Mechanism for recovering from mowing motors overheat during
automatic operation has failed
22 Frnt wheel prob. We exceeded the allowed front wheel detection time (drop-off)
23 Start elsewhere
Problem with the wire during Edge
We detected that all 4 wire sensors are outside the garden for too
long
24 Start elsewhere Problem with the wire during Edge
25 Start elsewhere
Problem with the wire during Edge
We are unable to locate the wire for too long
26 Start elsewhere Failure of the Wire Acquisition process
27 Start elsewhere Software problem
28 Start elsewhere Failure of the Wire Acquisition process rear bumper was detected
during Acquisition
29 Max dist reached We reached the maximal Edge distance during the “Learn Edge"
process
30 Docking problem Edge process was terminated before we reached the docking
station
31 Start elsewhere Software problem
32 Start elsewhere Software problem
5
33
Stop
cause
number
Message Description
33 Drive overload Mechanism for recovering from drive motors overheat during
automatic operation has failed
34 Check mow height
Mowing motors problem
Mowing motors are off but high currents are measured. This means
that either the mowing motors or the main board are damaged.
35 Start elsewhere Robot is stuck in place for too long during Edge operation
36 Check mow height
Mowing motors problem
High Mowing motors currents are detected after Mowing currents
calibration in GO (after mowing motors are activated for a few
seconds when robot is not moving).
37 Start elsewhere Software problem
38 Start elsewhere Software problem
39 Start elsewhere Software problem
40 Check mow height
Mowing motors problem
Too many over current events occurred during automatic mode.
41 Start elsewhere Software problem
42 Start elsewhere Software problem
43 Check mow height
Mowing motors problem
Over current event during manual mode
44 Start elsewhere Software problem
45 Docking problem Failure connecting to the docking station
46 Start elsewhere Software problem
47 Start elsewhere Software problem
48 Start elsewhere Software problem
49 Start elsewhere Problem with the wire sensors readings
50 Start elsewhere Software problem
51 Start elsewhere Problem with the wire sensors readings
52 Start elsewhere Software problem
53 Blocked path Path is blocked
54 No wire signal No wire signal during automatic operation
55 Frnt bumper disc Front bumper disconnected
56 Rear bumper disc Rear bumper disconnected
57 Frnt bmp pressed Front bumper pressed
58 Frnt bmp pressed Front bumper pressed
59 Rear bmp pressed Rear bumper pressed
61 Start inside All wire sensors are outside the plot when operation is initiated
62 Start elsewhere
Problem with the wire sensors readings
Wire synchronization failure
63 No wire signal No wire signal
64 Set country Set country
65 Calibration req. DK calibration is required
66 Enable dock on/off Enable/Disable docking station
67 Start elsewhere Software problem
68 Blocked path Bumper detection during manual mowing
69 No wire signal No wire signal is detected in one of the wire sensors
70 Start elsewhere Problem with the wire sensors readings
72 Start elsewhere Software problem
5
34
Stop
cause
number
Message Description
73 Start elsewhere Software problem
74 No message Power supply over heat detected during the charging process.
75 Start inside All wire sensors are outside the plot when operation is initiated
76 Frnt bumper disc Front bumper disconnected
77 Rear bumper disc Rear bumper disconnected
78 Time completed Working time expired
79 Start elsewhere Software problem
80 Start elsewhere Software problem
81 Start elsewhere Problem with the wire sensors readings
82 No wire signal No wire signal
83 No wire signal No wire signal detected during GO
85 Start elsewhere Problem with the wire sensors readings
86 Start elsewhere Problem with the wire sensors readings
87 No wire signal No wire signal
89 Start elsewhere Problem with the wire sensors readings
91 Start elsewhere Problem with the wire sensors readings
93 Start elsewhere Problem with the wire sensors readings
94 No wire signal No wire signal
95 No wire signal No wire signal
96 Recharge batt. Battery needs recharging
98 Start elsewhere Software problem
100 Check mow height Mowing motors problem
101 Mowing Overload Mowing motors overload
102 Drive overload Drive motors overload
103 Start elsewhere Problem with the wire sensors readings during Edge
104 Check signal
Interferences in the wire signal are detected. This can happen for
example in case user is working with the wrong wire signal type or
because interference from a nearby garden.
107 Start elsewhere Failure of the Wire Rescue maneuver
109 Start elsewhere Software problem
112 Stuck in place
Robot stuck monitor detection.
Robot is stuck in place for too long.
115 Bumper disc. Bumper disconnected
116 Bumper disc. Bumper disconnected
117 „Button name‟
pressed One of the remote‟s buttons is pressed during power up
118 Start elsewhere Problem with the wire sensors readings
119 Rain detected Rain detected
120 Replace blades Replace blades
121 Docking problem Robot did not succeed disconnecting from the docking
122 Docking problem Edge process was terminated before we reached the docking
station because perimeter island was detected
123 Docking problem Edge process was terminated before we reached the docking
station because we reached the required DK quarters
124 Docking problem Software problem
125 Docking problem
Edge process was terminated before we reached the docking
station because we reached the required edge distance that was
set by the user in this Zone
5
35
Stop
cause
number
Message Description
126 Docking problem Edge process was terminated before we reached the docking
station because we reached the required DK quarters
128 Max dist reached
We reached the maximal Edge distance during the “Wire position
test"
129 Test result: „result‟ Termination of the Edge termination test
130 Test result: „result‟ Termination of the docking station entry test
131 Docking problem We slided off the docking station more than 5 times during the
current charging process
132 Docking problem We slided off the docking station more than 5 times during the
current charging process
134 Low temperature Ambient temperature is too low for more than 12 hours during the
charging process
135 High temperature Ambient temperature is too high for more than 12 hours during the
charging process
136 Charging failure Charging problem
137 Charging failure Charging FET temperature is too high for more than 3 hours during
the charging process
138 Check P. switch Perimeter switch problem
139 Check Power No wire or charger voltage are detected in the docking station for
more than 1 minute
140 Check Power Charging problem
141 STOP button was pressed during automatic operation
142 Remote was taken out during automatic operation
143 Left/Mid/Right mow
problem Disconnected or burnt Left Right or Middle mowing motor
144 Stuck in place
Robot stuck monitor detection.
Robot is stuck in place for too long.
145
One of the following:
1. No wire signal
2. Mowing overload
3. Drive overload
4. Start inside
Auto-restart mechanism failure.
If “Start inside” is displayed then Automatic operation was
terminated because of wire escape.

seulement en anglais sorry....._o_

pas de probleme pour l'anglais ....
encore merci.

si je comprend bien la liste il s'agirai donc du code 141 : bouton stop ...

par contre personne n'a fait fonctionner le stop ...
bizarre.

JL

forcement ..... un voisin jaloux peut peut.... :)

il doit y avoir d autre cause d'arret non ?

bon et bien voila ....
ce jour encore plante au milieu du jardin.
je la relance
10 minutes apres : plantage de l'autre cote du jardin : message coince en place
je relance .... 2 minutes : coince en place.
je relance et regarde la machine ..... bizarre la roue avant est bizarre.

j'arrete le robot, souleve la bete et : la roue avant desolisarisee de son axe.

je pense que la cause est la. Pas de chance la machine est preseque neuve (15 jours).

cela arrive souvant ce genre de probleme ?


NB : demain je contacte le vendeur et on va voir la qualite du service apres vente ... (?)


JL

oui il suffit de changer la roue avant ( spp0011c ).
quand nous avons mis en place le système de detection de glissement, nous avons mis en place deux aimants dans les roues avant.
Au début sur quelques machines la fermeture de cette roue avais ete mal faite ur quelques machines. cela est corrigé maintenant.

j'ai une robomow rl1000 qui date d'avril 2010
j'avais posé mon cable peripherique un peu a l'arrache suite a pas mal de modifiction de parcours lors de l'installation juste en tortillant les fils!
j'avais souvent des pannes" plus de signal"
prenant mon courage a deux mains je viens de tout refaire propre en soudant les 10connexions et en y mettant une gaine rétractable

je lance la machine pour faire une zone determinée
elle a bien fait son pourtour elle est revenue a la base puis repartie et s'est dirigée ensuite vers le point de départ comme elle doit le faire
elle a marché environ 20 minutes et rebelotte "plus de signal!!j'ai controle dans la zone ou elle est passée et elle ne m'a pas coupé le fil
a la sation ça me dit fil coupé!!!
le dernier arret est 1.092
la hot line en hollande ne repond pas
si quelqu'un pouvait m'aider?

je me suis un peu emmelé les pinceaux je n'arrive pas a créer un nouveau sujet!!
désolé